OWNER S/OPERATOR S - PARTS MANUAL CEMENT MIXER MODEL MX-80

Transcription

1 OWNER S/OPERATOR S - PARTS MANUAL CEMENT MIXER MODEL MX-80 Read the Operator s Manual entirely. When you see this symbol, be aware that the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others will depend on it! BUY SMART INC WILCO BLVD., WILSON, NC PHONE - (252) FAX - (252) TOLL FREE PHONE (888)

2 INTRODUCTION This publication contains the instructions for use and maintenance of MX-80 Cement Mixer and general mixer for agricultural and other use. SAFETY RULES 1. Carefully read the operator s manual before working with the machine. 2. Check counter cowling supplied with mixer. 3. Keep a safe distance from the PTO Shaft during the work. HOW TO ATTACH THE MIXER The frame is designed to allow attachment of the mixer to tractors equipped with 3-point hydraulic lift system (Category 1&2). 1. Once attached to the tractor it is necessary to remove the blocking knobs from the support legs. 2. Place the mixer as shown in position B indicated in the diagram in this booklet and block the lift bars of the hydraulic lift so that the PTO Shaft remains horizontal with respect to the power take-off of the tractor and the input shaft of the cement mixer. There upon carry out the link up to the hydraulic system of the tractor verify, without rotating the mixer tub, that the PTO Shaft is in no way subjected to binding especially when in the position C of the diagram. 3. Start the power take-off of the tractor at the lowest RPM and rotate the mixer tub for a short period empty. During these tests ensure once again cross-pieces either in position A or position C of the diagram. MAINTENANCE Before starting work, the machine should be lubricated with care at points 1 and 2 indicated in the diagram, at the ball joints and sliding tubes of the PTO Shaft, and also on the chain drive system. Check the tension of the chain drive and if necessary, regulate with the tension control mechanism. Avoid operation at the angle of the PTO Shaft greater than the maximum of 35 o indicated on the decals. 1 08/04

3 ATTENTION! 1. Check the length of the PTO shaft, ensuring that it has a minimum axial play of (2 inches) in the shortest position (IT SHOULD UNDER NO CIRCUMSTANCES BIND). Check also the length of the PTO shaft at the point of full extension to ensure that the insert length between the two halves of the shaft is not less than (4inches). 2. It is good practice not to operate the PTO shaft with angulation over 35 degrees. Hence during the loading operation it is advisable to detach the PTO shaft from the implement. MIN INCHES MAX. 35 DEGREES 08/04 2

4 TECHNICAL DATA 2 A LOADING POSITION B 1 C UNLOADING POSITION Attachment to transmission Shaft: 1 1/8 Attachment to flexible hydraulic tube: 3/8 Hydraulic Pressure for Operation: Transmission Shaft rotation velocity: 725 PSI PSI Min Max 300 RPM Transmission Ratio: 10/1 Capacity of Mix Tub: Diameter of loading mouth: 84.5 gallons/11.2 cubic feet 1.45 ft Overall Dimension: Width: 2.82 ft. Length: 3.05 ft. Height: 3.12 ft. Weight (empty): 192 LBS 3 08/04

5 WAYS TO INSTALL PTO SHAFT Fig. 1 PTO Shaft is assembled on Mixer in the following way: - Put plastic cowling on PTO Shaft (fig.1) - thread the stud into the appropriate hole and - fasten with the shear pin (fig.2), - lean the cowling against support and fasten it with the supplied screws. Fig. 2 Fig. 3 08/04 4

6 5 08/04

7 ITEM# PART# DESCRIPTION QUANTITY 1 BAL Forward Spout X 2 BAL Tub Base X 3 BAL Agitator X 4 BAL Central Drive Shaft X 5 BAL Nut 10m X 6 BAL Washer X 7 BAL Bolt 14x40 X 8 BAL Washer 15m X 9 BAL Bolt 14x20 X 10 BAL Bolt 14x25 X 11 BAL Nut 8m X 12 BAL Washer 8m X 13 BAL Bolt 8x16 X 14 BAL Drive Chain 1/2 X 15 BAL Crown Gear z=114 X 16 BAL Pinion Gear z=13 X 17 BAL Clip Ring 30m X 18 BAL Ball Bearing 6006 X 19 BAL Support X 20 BAL Nut 12m X 21 BAL Bolt 12x35 X 22 BAL Grease Nipple 8m X 23 BAL Washer 12m X 24 BAL Self Lock Nut 12m X 08/04 6

8 7 08/04

9 ITEM# PART# DESCRIPTION QUANTITY 25 BAL Block Nob X 26 BAL Frame X 27 BAL Lift Pin X 28 BAL Ball Bearing 6209 X 29 BAL Cover X 31 BAL Bolt 16x30 X 33 BAL Nut 14m X 34 BAL R Cotter Pin X 35 BAL Lift Pin 3-Point X 36 BAL Cylinder Feed Tube X 38 BPT-032 PTO Shaft Complete X 39 BAL Right Support - Leg X 40 BAL Left Support - Leg X 41 BAL Chain Junction Link 1/2 X 42 BAL Clip Ring X 43 BAL Cylinder Tube X 46 BAL BK 4131 X 47 BAL O-Ring 4131 X 48 BAL Moved Head X 49 BAL O-Ring 3043 X 50 BAL TSE X 51 BAL GHM X 52 BAL Fixed Head X 53 BAL Seeger RB 40 X 08/04 8

10 9 08/04

11 ITEM# PART# DESCRIPTION QUANTITY 54 BAL Seeger E 35 X 55 BAL Cylinder Frame X 56 BAL Nut 12m X 57 BAL Safety Guard X 58 BAL ScrewX 59 BAL PTO Shaft Protection X 60 BAL Bolt 6x10 X - BAL Ring Kit X - BAL Cylinder Complete X 08/04 10

12 BUY SMART INC WILCO BLVD., WILSON, NC PHONE (252) FAX (252) TOLL FREE PHONE (888)