How To Install A Cisco Cisco 520-T1 Router On A Network Card (Cisco) With A Network Cable (Cio) And A Network (Cnet) (Coconc) (Net) And An Ipo (

Transcription

1 Quick Start Guide Cisco Small Business Pro SR 520-T1 Secure Router Package Contents SR 520-T1 Secure Router Ethernet Network Cable Console Cable AC Power Cord and AD/DC Power Adapter Power Cord Locking Latch Quick Start Guide CD-ROM

2 Welcome Thank you for choosing the Cisco SR 520-T1. The SR 520-T1, part of the Cisco Small Business Pro series, is a unified communications solution for small businesses that addresses the data T1 access needs of small business customers for data, voice, and video applications. This guide describes how to install your SR 520-T1 and how to launch the Configuration Utility and Cisco Configuration Assistant (CCA). Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide 1

3 1 Before You Begin Before you begin the installation, make sure that you have the following: Cables Ethernet cable for connecting LAN port to your administration computer (supplied). T1 cable for connecting the T1 port to your T1 source. An administration computer running: Windows Vista, or Windows XP (Service Pack 2) operating system Microsoft Internet Explorer 6.0 or later Adobe Flash Player version or later A registered account on Cisco.com. You need this so that you can download the CCA software necessary to configure your SR 520-T1. A number-2 Phillips screwdriver to connect the ground ring terminal to the chassis. Wire crimper to attach the ring terminal to a ground wire. Wire for connecting the chassis to ground: AWG 14 (2 mm 2 ) or larger wire for NEC-compliant chassis grounding. AWG 18 (1 mm 2 ) or larger wire for EN/IEC compliant chassis grounding. A ring terminal with an inner diameter of 1/4 in. (5 to 7 mm), for NECcompliant chassis grounding. 2 Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide

4 2 Getting to Know the SR 520-T1 The SR 520-T1 includes: WAN/T1 port 2 LAN ports Console port The SR 520-T1 can be installed in various types of network configurations. For information about planning, designing, and deploying the SR 520-T1 in your network, refer to the Smart Business Communications System Design Guide and Smart Business Communications System Basic Implementation Guide available on Cisco.com. See the documentation links in Where to Go From Here, on page 14. Front Panel The front panel contains the power (OK), LAN, and T1 status lights. OK LAN 0 1 CD T1 AL LED Description OK Solid green indicates normal operation. Blinking green indicates the SR 520-T1 is in the boot up phase. LAN 0 Solid or blinking green indicates LAN Activity on port 0. LAN 1 Solid or blinking green indicates LAN Activity on port 1. T1 CD Solid green indicates T1 carrier detect. T1 AL Solid amber indicates a T1 alarm condition. Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide 3

5 Back Panel Cisco SR520-T1 WAN/T1 1 LAN 0 12V DC SA WAN/T1 Port LAN Ports Console Port 12V DC Power On/Off Security Switch Slot Feature Description WAN/T1 port Use this port to connect the router to your T1. LAN port 0 Use this port to connect the router to your UC500, switch, or other network device. Use LAN port 0 to configure the SR 520-T1. LAN port 1 Use this port to connect the router to your UC500, switch, or other network device. This port is disabled by default. CONSOLE/AUX port Use this port to connect a console. Used in conjunction with the supplied console cable for disaster recovery. 12V DC Power Use this port to connect the power adapter. On/Off switch Use this switch to power the SR 520-T1 on or off. Security slot (Kensington type) Use this slot to connect a lock and cable to physically secure your router. CAUTION Use the LAN 0 port for administrative use. The LAN 1 port is a separate network and disabled by default. Default Settings Parameter Value Username cisco Password cisco LAN IP DHCP Range to Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide

6 3 Installing the SR 520-T1 NOTE Before proceeding, consider the location of the equipment with respect to reliable earth ground in accordance with local electrical safety standards. Placement Tips Storage Temperature (sea level) -40 F to 158 F (-40 C to +70 C) Operating Temperature (sea level) 32 F to 104 F (0 C to +40 C) Relative Humidity (sea level) 5 to 95% RH You can install the SR 520-T1 on a desktop or mount it in a rack. CAUTION Do not place anything on top of the router that weighs more than 5 pounds (2.25 kg), and do not stack routers on a desktop. Excessive distributed weight of more than 5 pounds, or pound point load of 5 pounds on top could damage the device. Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide 5

7 WAN/T1 1 LAN 0 CONSOLE 12V DC SA Rack Mounting NOTE With the optional rack mounting kit, Cisco part number , you can install the SR 520-T1 in a rack. STEP 1 STEP 2 Use four Phillips head screws to attach each bracket to the SR 520-T1 as illustrated. Install the router on the rack by using the screws required by your rack. AUX Grounding the Chassis Connect the chassis to a reliable earth ground in accordance with local electrical safety standards. For NEC-compliant grounding, use size AWG 14 (2 mm 2 ) or larger wire and an appropriate ring terminal. For EN/IEC compliant grounding, use size AWG 18 (1 mm 2 ) or larger wire and an appropriate ring terminal. 6 Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide

8 STEP 1 STEP 2 Strip one end of the ground wire and connect it to a ring terminal using a crimp tool. Attach a ring terminal to the chassis. Use a number-2 Phillips screwdriver, and tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m). FXS CONSOLE WAN/T1 1 LAN 0 AUX 12V DC 2.5A Ring terminal STEP 3 Connect the other end of the ground wire to a known reliable grounding point at your site. Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide 7

9 4 Connecting the Equipment STEP 1 STEP 2 Connect the included power cord to the 12V DC Power port on the SR 520-T1. To secure the power cord to the SR 520-T1, attach the Power Cord Locking Latch to the power cord, and slide the clip to the end of the plug. Refer to the illustration below. CONSOLE WAN/T1 1 LAN 0 AUX 12V DC SA Power Cord Locking Latch Power Cord A/C Plug Power Adapter STEP 3 STEP 4 Insert the A/C plug into an electrical outlet. Press the On switch. The OK LED on the front panel blinks green while the SR 520-T1 boots. After booting, the OK LED remains solid green. 8 Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide

10 STEP 5 Connect a cable from your T1 jack to the WAN/T1 port on the back panel of your SR 520-T1. NOTE STEP 6 Connect either a T1 straight-through cable (identical to an Ethernet straight-through cable), or a T1 crossover cable. The cable that you use depends on the type of termination of the wiring at your site. Connect an Ethernet cable from your administration computer to the LAN 0 port of the SR 520-T1. CAUTION Do not connect your administration computer to the LAN 1 port on the SR 520-T1. NOTE When your administration computer is plugged into LAN 0, it will be configured on subnet 75 via DHCP. You will be able to use your web browser to configure the SR 520-T1 as explained in Section 6. Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide 9

11 5 Verifying the Hardware Installation To verify the hardware installation, complete the following tasks: Check the OK LED status. The LED should be solid green indicating that the SR 520-T1 has power and is ready to use. Check the LAN 0 LED status. The LED should be solid green or blinking green to indicate that the SR 520-T1 is connected to the administration computer. Make sure that you are using Category 5 or better Ethernet cables to connect from the administration computer and the SR 520-T1. 10 Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide

12 6 Getting Started with the Configuration SR 520-T1 Configuration Utility The SR 520-T1 Configuration Utility guides you through the steps needed to configure the SR 520-T1. NOTE Before starting the SR 520-T1 Configuration Utility, obtain the T1 connection information from your service provider. Ensure that your administration computer is running the following software: Windows Vista, or Windows XP (Service Pack 2) operating system Microsoft Internet Explorer 6.0 or later Adobe Flash Player version or later Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide 11

13 STEP 1 STEP 2 STEP 3 Start a web browser on your computer, and enter the following URL: The browser displays the first page of the SR 520-T1 Configuration Utility. The Configuration Utility will guide you through the installation process; follow the on-screen instructions. Default user name: cisco Default password: cisco When you reach the ApplyAndTest page of the Configuration Utility, click Apply and Test. Follow the on-screen instructions to resolve any issues if necessary. After you have successfully completed the Configuration Utility, the Congratulations screen appears. The basic installation of the SR 520-T1 is complete and you are now ready to start using your SR 520-T1. 12 Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide

14 7 Suggested Next Steps The SR 520-T1 is pre-configured with default settings that allow you to begin using the device right away. However, you might want to change the default settings or perform other tasks using Cisco Configuration Assistant (CCA). Downloading Cisco Configuration Assistant Cisco Configuration Assistant is a PC-based application that Cisco provides free-of-charge to simplify the task of configuring, deploying, and administering the SR 520-T1 and the other components of the Cisco Smart Business Pro family. STEP 1 STEP 2 STEP 3 Start a web browser, and enter the following address (Cisco log on required): Click Download Software link. On the Download page, be sure to choose Cisco Configuration Assistant. NOTE Ensure that you choose Cisco Configuration Assistant version or later. STEP 4 STEP 5 STEP 6 After the file is downloaded, run the Installer (EXE file). Ensure that an Ethernet cable is connected from your administration computer to the LAN 0 port of the SR 520-T1. Follow the instructions to install the CCA on your administration computer. For further information about managing and administering your SR 520-T1, refer to the CCA online help or Cisco Configuration Assistant Smart Business Communications System Administrator Guide. See the product documentation links in Where to Go From Here, on page 14. NOTE Use port 0 to connect to Cisco Unified 500 Series products. Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide 13

15 8 Where to Go From Here Support Cisco Small Business Support Community Online Technical Support and Documentation (Login Required) Phone Support Contacts Software Downloads (Login Required) Product Documentation Cisco Configuration Assistant Smart Business Communications System Administrator Guide Cisco Smart Business Communications System Basic Implementation and Design Guides Cisco Unified Communications 500 Series for Small Business Cisco Small Business Cisco Partner Central for Small Business (Partner Login Required) Cisco Small Business Home Marketplace small_business_support_center_contacts.html Go to tools.cisco.com/support/downloads, and enter the model number in the Software Search box. tsd_products_support_series_home.html products_implementation_design_guides_list. html (Partner Login Required) Cisco Small Business Pro SR 520-T1 Secure Router Quick Start Guide

16 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA Tel: NETS (6387) Fax: Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R) 2009 Cisco Systems, Inc. All rights reserved. Printed in the USA on recycled paper containing 10% postconsumer waste