Connector and Cable Specifications
|
|
|
- Josephine Fox
- 10 years ago
- Views:
Transcription
1 APPENDIX B This appendix provides the following cabling and pinout information for the Cisco IAD1101 integrated access device: Console Port Signals and Pinouts Ethernet Connector Pinouts Analog Subscriber Connector Signals and Pinouts T1 Port Pinouts Serial Port (V.35) Connector Signals and Pinouts Note This appendix specifies pinouts only for the pins used. Pins not listed in the tables in this appendix are not connected. Console Port Signals and Pinouts Use the yellow Ethernet (straight) cable and RJ-45-to-DB-9 female DTE adapter to connect the console port to the serial port on a Windows NT workstation with EMS and Dial-up Networking installed. Table B-1 lists the pinouts for the asynchronous serial console port, the RJ-45-to-DB-9 female DTE adapter, and the workstation serial port. Note To configure your Windows NT workstation for Dial-up Networking access to the Cisco IAD1101 through the console port, see the RS-232 Connection application note. Table B-1 Console Port Signaling and Cabling Using a DB-9 Adapter Console Port (DTE) RJ-45 to DB-9 Adapter Workstation Serial Port Signal Pin Type RJ-45 Pin DB-9 Pin Signal No Signal 1 9 RI RD_TX_MISC Output 2 1 DCD DTR Input 3 4 DTR Ground 4 5 TxD Output 5 2 RxD B-1
2 Ethernet Connector Pinouts Appendix B Table B-1 Console Port Signaling and Cabling Using a DB-9 Adapter (continued) Console Port (DTE) RJ-45 to DB-9 Adapter Workstation Serial Port Signal Pin Type RJ-45 Pin DB-9 Pin Signal RxD Input 6 3 TxD RD_TX_MISC Output 7 8 CTS No Signal 8 7 RTS 6 DSR Ethernet Connector Pinouts Figure B-1 shows the Ethernet 10BaseT connector (RJ-45) and Table B-2 lists its pinouts. Figure B-1 10BaseT Connector H7316 Table B-2 10BaseT Connector (RJ-45) Pinouts Pin Description 1 TX+ 2 TX- 3 RX RX- 7 8 B-2
3 Appendix B Analog Subscriber Connector Signals and Pinouts Analog Subscriber Connector Signals and Pinouts Figure B-2 shows the analog subscriber connector (Amp-Champ) and Table B-3 lists its pinouts. Figure B-2 Analog Subscriber Connector 50-Pin Male Champ connector Pin 1 Pin 25 Pin 26 Pin 50 Mating side view Table B-3 Analog Subscriber Connector Pinouts Circuit Pin (Ring) Pin (Tip) FXS FXS FXS FXS FXS FXS FXS FXS FXS FXS FXS FXS FXS FXS FXS FXS Expansion Expansion Expansion Expansion Expansion Expansion Expansion B-3
4 T1 Port Pinouts Appendix B Table B-3 Analog Subscriber Connector Pinouts (continued) Circuit Pin (Ring) Pin (Tip) Expansion Not Used T1 Port Pinouts Figure B-3 shows the RJ-48 connector wiring for the T1 trunk cable, and Table B-4 lists the pinouts. Figure B-3 RJ-48-to-RJ-48 T1 Cable Wiring 1 8 H11419 Table B-4 T1 Port (RJ-48) Pinouts Pin Description 1 RX Tip 2 RX Ring 3 4 TX Tip 5 TX Ring B-4
5 Appendix B Serial Port (V.35) Connector Signals and Pinouts Serial Port (V.35) Connector Signals and Pinouts The serial port on the Cisco IAD1101 is a 26-pin connector supporting V.35 DTE connections. Serial (26-pin) to V.35 Cable Assembly Figure B-4 shows the wiring for the serial to V.35 cable, and Table B-5 lists the DCE pinouts. Arrows indicate signal direction: means DTE to DCE and means DCE to DTE. Figure B-4 26-Pin Serial DTE to V.35 DCE Cable Wiring J1-26 J1-14 J1-13 J1 J J2-MM J2-KK J2 J2-C J2-A J2-LL J2-NN J2-B J2-D Table B-5 V.35 DCE Serial Cable Pinout Serial Connector Pin Signal Name Note Direction Signal Name V.35 Pin J1-22 J1-23 MODE_1 MODE_0 Local connections Drain wire Shield Shield_ J2-A J1-11 J1-12 J1-08 J1-07 J1-06 J1-19 I_CTS/RTS+ I_DSR/DTR+ O_RTS/CTS+ O_DTR/DSR+ B_DCD/DCD+ _ Twisted pair #4 Twisted pair #2 Twisted pair #1 RTS DTR CTS DSR RLSD J2-C J2-H J2-D J2-E J2-F B-5
6 Serial Port (V.35) Connector Signals and Pinouts Appendix B Table B-5 V.35 DCE Serial Cable Pinout (continued) Serial Connector Pin Signal Name Note Direction Signal Name V.35 Pin J1-13 J1-26 J1-05 J1-18 J1-01 J1-14 J1-04 J1-17 J1-02 J1-15 J1-03 J1-16 B_LL/LL+ I_RXD/TXD+ I_RXD/TXD- O_TXD/RXD+ O_TXD/RXD- I_RXC/TXCE+ I_RXC/TXCE- O_TXCE/RXC+ O_TXCE/RXC- B_TXC/TXC+ B_TXC/TXC- Twisted pair #3 Twisted pair #5 Twisted pair #9 Twisted pair #6 Twisted pair #8 Twisted pair #7 LT SD+ SD- RD+ RD- SCTE+ SCTE- SCR+ SCR- SCT+ SCT- J2-K J2-B J2-P J2-S J2-R J2-T J2-U J2-W J2-V J2-X J2-Y J2-AA Serial (26-pin) to Serial (26-pin) Cable Assembly Figure B-5 shows the wiring for the 26-pin serial DTE to serial DCE cable, and Table B-6 lists the pinouts. Arrows indicate signal direction: means DTE to DCE and means DCE to DTE. Figure B-5 26-Pin Serial DTE to 26-Pin Serial DCE Cable Wiring J1-26 J1-14 J1-13 J1 J1-1 J2-1 J2 J2-13 J2-14 J B-6
7 Appendix B Serial Port (V.35) Connector Signals and Pinouts Table B-6 DTE to DCE Serial Cable Pinout DTE Serial Pin Signal Name Note Direction Signal Name DCE Serial Pin J1-22 J1-23 J1-24 J1-08 J1-07 J1-11 J1-12 J1-06 J1-19 J1-13 J1-26 J1-01 J1-14 J1-05 J1-18 J1-02 J1-15 J1-04 J1-17 J1-03 J1-16 MODE_1 MODE_0 MODE_DCE O_RTS/CTS+ O_DTR/DSR+ I_CTS/RTS+ I_DSR/DTR+ B_DCD/DCD+ _ B_LL/LL+ O_TXD/RXD+ O_TXD/RXD- I_RXD/TXD+ I_RXD/TXD- O_TXCE/RXC+ O_TXCE/RXC- I_RXC/TXCE+ I_RXC/TXCE- B_TXC/TXC+ B_TXC/TXC- Local connections Shield Twisted pair #4 Twisted pair #2 Twisted pair #1 Twisted pair #3 Twisted pair #5 Twisted pair #9 Twisted pair #6 Twisted pair #8 Twisted pair #7 MODE_1 MODE_0 I_CTS/RTS+ I_DSR/DTR+ O_RTS/CTS+ O_DTR/DSR+ B_DCD/DCD+ _ B_LL/LL+ I_RXD/TXD+ I_RXD/TXD- O_TXD/RXD+ O_TXD/RXD- I_RXC/TXCE+ I_RXC/TXCE- O_TXCE/RXC+ O_TXCE/RXC- B_TXC/TXC+ B_TXC/TXC- J2-22 J2-23 J2-11 J2-12 J2-08 J2-07 J2-06 J2-19 J2-13 J2-26 J2-05 J2-18 J2-01 J2-14 J2-04 J2-17 J2-02 J2-15 J2-03 J2-16 B-7
8 Serial Port (V.35) Connector Signals and Pinouts Appendix B B-8
Cable Specifications
APPENDIX C Cable Specifications This appendix provides the following pinout information: Console Port Pinouts (RJ-45), Table C-1 Auxiliary Port Pinouts (RJ-45), Table C-2 EIA-530 DTE Cable Pinout (DB-60
Frame Relay Cabling This section describes the cabling and connector pinouts for the Frame Relay cards.
A P P E N D I B Cabling Summary Introduction This appendix contains details on the MG 8850 cabling. Note In all cable references, the transmit direction is away from the switch, and the receive direction
Cable Specifications and Information
APPENDIXA This appendix provides the connector and pinout information you need for making or purchasing cables used with Cisco VG350 Voice Gateway. To order cables from Cisco, see the Obtaining Technical
Cable Pinouts. SRP I/O Module
Cable Pinouts C This appendix lists the cables and connector pinout assignments for the cables used with the ERX-700 series and ERX-1400 series. Topic Page SRP I/O Module C-1 CT1 and CE1 I/O Modules C-4
Cable Specifications and Information
APPENDIX A This appendix provides the connector and pinout information you need for making or purchasing cables used with Cisco VG224 voice gateway. To order cables from Cisco, see the Obtaining Technical
Connectors and Cables
APPENDIX B This appendix describes the connectors, cables, and adapters that you use to connect the switch to other devices. Connector Specifications 10/100 Ports The 10/100 Ethernet ports use standard
RS-232 COMMUNICATIONS
Technical Note D64 0815 RS-232 COMMUNICATIONS RS-232 is an Electronics Industries Association (EIA) standard designed to aid in connecting equipment together for serial communications. The standard specifies
Connector and Cable Specifications
APPENDIXB This chapter describes the connector and cable specifications. Connector Specifications, page B-1l Cable and Adapter Specifications, page B-5 Connector Specifications 10/100/1000 Ports, page
Cable Specifications. T3 Trunk Cabling APPENDIX
APPENDIX B This appendix contains details on the MGX 8230 cabling. It includes the following sections: T3 Trunk Cabling Frame Relay Cabling DC Power Cabling AC Power Cabling Control and Clock Cabling External
RJ45 Shielded (standard) port pinout. CS9000, Jetstream 4000 + 8500, Lanstream 2000, RTA8/RJX, RRC16, MTA8/RJX & SXDC8/RJX
Shielded (standard) port pinout Pin Circuit Function 1 DCD Input Data Carrier Detect 2 DSR Output Data Set Ready 3 DTR Input Data Terminal Ready 4 S/GND Signal Ground 5 TXD Output Transmit Data 6 RXD Input
Cabling Specifications
APPENDIX A This appendix provides cabling and pinout information for feature cards on the Cisco AS5350XM and Cisco AS5400XM universal gateways. It contains the following sections: 2-Port and 4-Port T1
Encore Controller to Router Connections
Encore Presentation System Encore Controller to Router Connections Contents: Scope... 2 EXT COMM Pinouts... 2 Cable Connection Straight Through... 3 Cable Connection Null Modem... 3 Lantronix Ethernet
RJ11 RS-232 Interface
H NS TN30 RJ11 RS-232 Interface 1.0 General The back panel of the CPP-3794 provides a combination of 9 pin DB connectors and RJ11 connectors for connecting RS-232 serial cables. The 9 pin DB connector
Making a DB to RJ45 adapter.
Making a DB to RJ45 adapter. DB9 to RJ45 adapters are often used in combination with a RS232 repeater for extending the distance of a serial RS232 link, but can be used for any adapter or converter purposes.
Cabling Guide for Console and AUX Ports
Cabling Guide for Console and AUX Ports Contents Introduction Prerequisites Requirements Components Used Conventions Table of Routers with Console and AUX Ports Console Port Settings for Terminal Connection
Cisco - Ethernet 100BaseTX and 10BaseT Cables: Guidelines and Specifications
Page 1 of 8 Ethernet 100BaseTX and 10BaseT Cables: Guidelines and Specifications Contents Introduction Prerequisites Requirements Components Used Conventions Which Cable Do I Need? Ethernet Cabling Guidelines
Cable Guide. Click on the subject to view the information. Digi Cables Building Cables General Cable Information
Cable Guide Click on the subject to view the information. Digi Cables Building Cables General Cable Information Digi Cables Click on the subject to view the information. Digi Connector Options Digi Connector
Comtrol Cable User Guide
Comtrol Cable User Guide Trademark Notices Comtrol and DeviceMaster are trademarks of Comtrol Corporation. PortVision is a registered trademark of Comtrol Corporation. Microsoft and Windows are registered
Cable Guide Including all PortServer TS, Digi Connect, and Digi One Products
Cable Guide Including all PortServer TS, Digi Connect, and Digi One Products 90000253_E Digi International Inc. 2005. Digi, Digi International, the Digi logo, the Making Device Networking Easy logo, Digi
Serial Cables & Adapters
WTI Part No. 9 Rev. B Serial Cables & Adapters for WTI Products . Introduction This publication describes the serial cables and snap adapters that are used to connect your RSM-R series or MPC series unit
Product Overview. Features CHAPTER
CHAPTER 1 This chapter describes the Cisco IAD1101 integrated access device chassis, and the line interface modules supported by the Cisco IAD1101. This chapter includes the following sections: Features
Cable Guide For all PortServer TS, Digi Connect, and Digi One Products
Cable Guide For all PortServer TS, Digi Connect, and Digi One Products 90000253_F Digi International Inc. 2011. Digi, Digi International, the Digi logo, Digi One, Digi Connect, PortServer TS, and RealPort
Connecting Serial Interface Cards to a Network
CHAPTER 3 This chapter describes how to connect Cisco serial interface cards to a network and contains the following sections: Serial WAN Interface Cards (WICs), page 3-1 Serial High Speed WICs (HWICs),
Cable Guide For all PortServer TS, Digi Connect, and Digi One Products
Cable Guide For all PortServer TS, Digi Connect, and Digi One Products 90000253_G Digi International Inc. 2013. Digi, Digi International, the Digi logo, Digi One, Digi Connect, PortServer TS, and RealPort
IPG/7700 Hardware Manual SYSTECH. Document number 80-001099-7 Revision A
IPG/7700 Hardware Manual SYSTECH C O R P O R A T I O N Document number 80-001099-7 Revision A Created 2010, and Protected Under the U.S. Copyright Act of 1976. Copyright 2010, SYSTECH Corporation All Rights
Hardware Reference. Linux Device Server IGW/922 with DIL/NetPC ADNP/9200
Linux Device Server IGW/922 with DIL/NetPC ADNP/9200 Hardware Reference SSV Embedded Systems Heisterbergallee 72 D-30453 Hannover Phone: +49 (0)511/40 000-0 Fax: +49 (0)511/40 000-40 E-mail: [email protected]
Connecting the Console Port to a PC
This document covers tasks associated with connecting a console port to a PC, and includes the following topics: Console (rollover) Cable and Adapters Making the physical connection Connecting using HyperTerminal
isco Connecting Routers Back to Back Through the AUX P
isco Connecting Routers Back to Back Through the AUX P Table of Contents Connecting Routers Back to Back Through the AUX Ports...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1
Data Bulletin. Communications Wiring for POWERLINK G3 Systems Class 1210 ABOUT THIS BULLETIN APPLICATION INTRODUCTION.
Data Bulletin 1210DB0002R3/05 03/2005 LaVergne, TN, USA Communications Wiring for POWERLINK G3 Systems Class 1210 Retain for future use. ABOUT THIS BULLETIN This data bulletin describes the proper wiring
2-Port RS232/422/485 Combo Serial to USB2.0 Adapter (w/ Metal Case and Screw Lock Mechanism) Installation Guide
2-Port RS232/422/485 Combo Serial to USB2.0 Adapter (w/ Metal Case and Screw Lock Mechanism) Installation Guide 1. Introduction Thank you for purchasing this 2-Port RS232/422/485 Combo Serial to USB Adapter.
Application Note: Extending a TSP s Analog Capabilities Using an Access Bank I
22116 23 rd Drive SE Bothell, WA 98021-4413, USA Toll free 800-426-3926 425-487-1515 Fax 425-487-2288 E-mail [email protected] www.teltone.com Application Note: Extending a s Analog Capabilities Using an
XPort Universal Demo Board User Guide
XPort Universal Demo Board User Guide Part Number 900-563 Revision A September 2009 Copyright and Trademark Contacts 2009 Lantronix. All rights reserved. No part of the contents of this book may be transmitted
RS232C < - > RS485 CONVERTER S MANUAL. Model: LD15U. Phone: 91-79-4002 4896 / 97 / 98 (M) 0-98253-50221 www.interfaceproducts.info
RS232C < - > RS485 CONVERTER S MANUAL Model: LD15U INTRODUCTION Milestone s model LD-15U is a RS232 to RS 485 converter is designed for highspeed data transmission between computer system and or peripherals
IMACS. Cable and Equipment Guide. Premisys Communications. Integrated Multiple Access Communications Server. Publication 000-001903 Revision A2
IMACS Integrated Multiple Access Communications Server Cable and Equipment Guide Premisys Communications Publication 000-001903 Revision A2 February 1999 Trademarks: Premisys is a registered trademark
ISHIDA BC-3000. Scale to Scale Communications
ISHIDA BC-3000 Scale to Scale Communications Setup Procedure & Operating Instructions March 2006 PN 94561 Revision History Date Page Description March 2006 Initial publication August 2006 2 Added RS-232
One Port Serial Server Users Manual Model ESP901, ESP901E
One Port Serial Server Users Manual Model ESP901, ESP901E Documentation Number: ESP901-2303 International Headquarters B&B Electronics Mfg. Co. Inc. 707 Dayton Road -- P.O. Box 1040 -- Ottawa, IL 61350
Module Connectors and Cable Specifications
Module Connectors, page 1 Cables and Adapters, page 2 Cleaning the Fiber-Optic Connectors, page 6 Module Connectors RJ-45 Connector The RJ-45 connector is used to connect a Category 3, Category 5, Category
RS-232 Cables, Wiring and Pinouts. Brief tutorial and pinouts for RS-232, T1/E1 and V.35. Contents
RS-232 Cables, Wiring and Pinouts Brief tutorial and pinouts for RS-232, T1/E1 and V.35. Contents DTE (PC) and DCE (Modem) DB9 and DB25 Male and Female Pin Numbering RS232 on DB25 Pinout (RS-232C) RS232
FOM-5A, 6A. Asynchronous Fiber Optic Modem
FOM-5A, 6A Asynchronous Fiber Optic Modem FEATURES Asynchronous transmission at up to 19.2 kbps Transmission range up to 3 km (1.8 mi), regardless of data rate Full- or half-duplex Transfers one control
RS-232/422/485, Power over Ethernet
IP-COM-M IP-COMi-M IP-COM-M PoE IP-COMi-M PoE RS-232 RS-232/422/485 RS-232, Power over Ethernet RS-232/422/485, Power over Ethernet Edition: September 2012 The computer programs provided with the hardware
Using HyperTerminal with Agilent General Purpose Instruments
Using HyperTerminal with Agilent General Purpose Instruments Windows HyperTerminal can be used to program most General Purpose Instruments (not the 531xx series counters) using the RS-232 Serial Bus. Instrument
Cisco Modular Access Router Cable Specifications
Cisco Modular Access Router Cable Specifications This document provides cable specifications for Cisco 3600 series and Cisco 2600 series routers. Use this document in conjunction with the following publications:
Appendix A. This Appendix includes the following supplemental material:
Appendix A This Appendix includes the following supplemental material: Cabling Diagrams and Instructions Connectors (9-pin D-type) Data Transfer Protocols Usage/Handshaking Ultimax Dual Screen Console
Advanced Data Capture and Control Systems
Advanced Data Capture and Control Systems Tronisoft Limited Email: [email protected] Web: www.tronisoft.com RS232 To 3.3V TTL User Guide RS232 to 3.3V TTL Signal Converter Modules P/N: 9651 Document
16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide
16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide 1. Introduction Thank you for purchasing this 16-Port RS232 to USB2.0 High Speed Multi Serial Adapter. It is an
MDM192 MULTI-DROPS DIGITAL MODEM FOR PRIVATE LINE. USER GUIDE Document reference : 9010709-03
MDM192 MULTI-DROPS DIGITAL MODEM FOR PRIVATE LINE USER GUIDE Document reference : 9010709-03 If you have questions about the MDM192 or desire assistance, contact ETIC TELECOMMUNICATIONS at the following
User Manual IC-485AI 2002-09-27
User Manual IC-485AI Note: This equipment has been tested and found to comply ith the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
Hardware Installation and Configuration Guide
Hardware Installation and Configuration Guide Trademark Notices Comtrol, DeviceMaster, and PortVision are registered trademarks of Comtrol Corporation. Ethernet is a registered trademark of Digital Equipment
1.1 Connection. 1.1.1 Direct COM port connection. 1. Half duplex RS232 spy cable without handshaking
POS function Marchen POS-DVR surveillance system is a professional surveillance integrated with POS system. By bringing video and POS transaction data together, the POS-DVR surveillance system provides
Modbus Communications for PanelView Terminals
User Guide Modbus Communications for PanelView Terminals Introduction This document describes how to connect and configure communications for the Modbus versions of the PanelView terminals. This document
ETM9350-1/9400-1 Quick Start Guide
GSM/GPRS Terminal ETM9350-1 HSDPA/UMTS/GSM/GPRS Terminal ETM9400-1 Cinterion EU3-P Inside ETM9400-1 TC63i Inside ETM9350-1 ETM9350-1/9400-1 Quick Start Guide Features: 3G (HSDPA/UMTS) Connectivity ETM9400-1
Dial-Up / Leased-Line Modem. User Manual. AGM Electronics, Inc Dial-Up / Leased-Line Modem, Series ( ) 5019-1 Manual Rev A + - DLM CTS RTS DTR DSR
AGM Electronics, Inc Dial-Up / Leased-Line Modem, Series ( ) 5019-1 Manual Rev A User Manual + - CD CTS RTS DTR. DSR RI RX TX PHONE LINE DLM Dial-Up / Leased-Line Modem Dial-Up / Leased-Line Modem CONTENTS
LOW COST GSM MODEM. Description. Part Number
Dual Band 900 / 1800 MHz Fax, SMS and Data Integral SIM Card holder Siemens TC-35i GSM Engine Rugged Extruded Aluminium Enclosure Compact Form Factor 86 x 54 x 25mm RS232 Interface with Auto baud rate
Table of Contents. Page Number. PLC Connections 1 Cable Solutions for Omron PLCs 11 Cable Solutions for Multi-Vendor PLCs 15
Table of Contents Name Page Number PLC Connections 1 Cable Solutions for Omron PLCs 11 Cable Solutions for Multi-Vendor PLCs 15 i Reference Information PLC Connections The following pages illustrate the
ALL-USB-RS422/485. User Manual. USB to Serial Converter RS422/485. ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
ALL-USB-RS422/485 USB to Serial Converter RS422/485 User Manual ALL-USB-RS422/485 USB to RS-422/485 Plugin Adapter This mini ALL-USB-RS422/485 is a surge and static protected USB to RS-422/485 Plugin Adapter.
SyncLink GT2/GT4 Serial Adapter
SyncLink GT2/GT4 Serial Adapter Hardware User s Manual MicroGate Systems, Ltd http://www.microgate.com MicroGate and SyncLink are registered trademarks of MicroGate Systems, Ltd. Copyright 2008 2012 MicroGate
GM1200E Interface Cable
GM00E Interface Cable SPK+ Mic Aud Ext PTT SPK/0 Ext Alrm RJ Plug PTT/0 Flat Tx Audio SCI Data In SCI Data Out Emerg/ NPD In Motorola Accessory Connector (rear view) 0 Ign Det Flat Rx Audio CTS SW B+ Hook
Application Note 2. Using the TCPDIAL & TCPPERM Commands to Connect Two TransPort router Serial Interfaces Over TCP/IP.
Application Note 2 Using the TCPDIAL & TCPPERM Commands to Connect Two TransPort router Serial Interfaces Over TCP/IP. Reverse Telnet or Serial Terminal Server MultiTX feature UK Support March 2014 1 Contents
ELAN DIGITAL SYSTEMS LTD. SL232 PC- CARD USER S GUIDE
ELAN DIGITAL SYSTEMS LTD. LITTLE PARK FARM ROAD, SEGENSWORTH WEST, FAREHAM, HANTS. PO15 5SJ. TEL: (44) (0)1489 579799 FAX: (44) (0)1489 577516 e-mail: [email protected] website: http://www.pccard.co.uk
Cable Connection Procedures for Cisco 1900 Series Routers
CHAPTER 5 Cable Connection Procedures for Cisco 1900 Series Routers This document describes how to connect your Cisco 1941 integrated services router to a power source and to networks and external devices.
The Analyst RS422/RS232 Tester. With. VTR, Monitor, and Data Logging Option (LOG2) User Manual
12843 Foothill Blvd., Suite D Sylmar, CA 91342 818 898 3380 voice 818 898 3360 fax www.dnfcontrolscom The Analyst RS422/RS232 Tester With VTR, Monitor, and Data Logging Option (LOG2) User Manual Manual
MODBUS TCP to RTU/ASCII Gateway. User s Manual
MODBUS TCP to RTU/ASCII Gateway User s Manual 1 INTRODUCTION... 1 1.1 FEATURES... 2 1.2 PRODUCT SPECIFICATIONS... 3 1.3 DEFAULT SETTINGS... 4 2 MAKING THE HARDWARE CONNECTIONS... 5 2.1 POWER CONNECTION...
Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000
Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000 1.0 Introduction A Technical Application Note from Doppler System July 5, 1999 Version 3.x of the DDF6000, running version
USB TO SERIAL ADAPTER
USB TO SERIAL ADAPTER (Model: U232-P9V2) SPECIFICATIONS CONTENTS 1. GENERAL SPECIFICATIONS... 1 1.1 PRODUCT SURFACE... 1 1.2 PRODUCT DIMENSION... 2 1.3 PRODUCT FEATURES... 3 1.4 PRODUCT SPECIFICATIONS...
When we look at the connector pinout of the RS232 port, we see two pins which are certainly used
1 Null modem - an introduction Serial communications with RS232 1. One of the oldest and most widely spread communication methods in computer world. The way this type of communication can be performed
Adit 600 Product Guide
Adit 600 Product Guide Adit 600 R8.0 Broadband Customer Service Terminal which fulfills many channel bank, multiport CSU/DSU, Integrated Access Device, distributed DLC and Digital Cross-connect applications.
How To Run An Nport I5000A Device Server
NPort IA5000A Series 1, 2, and 4-port serial device servers for industrial automation Enhanced surge protection for serial, LAN, and power 2 KV isolation for serial signals Rugged screw-type terminal blocks
VOICE RECORDING SYSTEM ISDN PRI / BRI
Sense Box VOICE RECORDING SYSTEM ISDN PRI / BRI / Analog SUB-SYSTEM ISDN2, ISDN30 Sense Box USER MANUAL TABLE OF CONTENTS 1. STATUTORY INFORMATION... 3 1.1 SAFETY WARNING... 3 1.2 SAFETY EXTRA LOW VOLTAGE
Installation & Configuration Manuel. Socket Server. OpenAT application
Installation & Configuration Manuel Socket Server OpenAT application 2009 / 05 / 29 2 ! CAUTION! ELECTRIC SHOCK HAZARD IF COVER REMOVED SERVICE BY QUALIFIED PERSONEL ONLY Document History Date Version
LBNP16312. RS-232/485/422 serial device server. User manual
Tu Sitio de Automatización! LBNP16312 RS-232/485/422 serial device server User manual Summarize-----------------------------------------------------------------------------14-3 Package checklist---------------------------------------------------------------------14-3
Application Note 83 Fundamentals of RS 232 Serial Communications
Application Note 83 Fundamentals of Serial Communications Due to it s relative simplicity and low hardware overhead (as compared to parallel interfacing), serial communications is used extensively within
How To Set Up A 366101 Modem (Marc) Model 366101 (Marc) Model 2 (Marr) Model 1 (Marm) Model 4 (Mariar) Model 8 (Marp) Model 6 (Mar
DIN Rail Mounted Leased Line Modem Users Manual 366-101 Rev. 2 Copyright 2008 Miille Applied Research Co., Inc. Houston, Texas This page is left blank intentionally Page i TABLE OF CONTENTS LIST OF FIGURES...
Manual Serial PCI Cards
Manual Serial PCI Cards W&T Models 13011, 13410 13411, 13610 13611, 13812 Version 1.4 Subject to error and alteration 37 01/2005 by Wiesemann & Theis GmbH Subject to errors and changes: Since we can make
HARDWARE MANUAL. BrightSign HD120, HD220, HD1020. BrightSign, LLC. 16795 Lark Ave., Suite 200 Los Gatos, CA 95032 408-852-9263 www.brightsign.
HARDWARE MANUAL BrightSign HD120, HD220, HD1020 BrightSign, LLC. 16795 Lark Ave., Suite 200 Los Gatos, CA 95032 408-852-9263 www.brightsign.biz TABLE OF CONTENTS OVERVIEW... 1 Block Diagram... 2 Ports...
TCP/IP Converter DDS EX-9132 Operation Manual for 8051 Series
TCP/IP Converter DDS EX-9132 Operation Manual for 8051 Series First Edition, March 2005 Table of Contents 1. Introduction 3 Overview 4 Package Checklist 5 Block Diagram 6 Features 7 Product Specifications
CX-U Series Hardware Reference Manual
CX-U Series Hardware Reference Manual COPYRIGHTS AND DISCLAIMERS Hardware Revision number: CX-U rev 6 Published Date: September 2009 This publication contains information proprietary and confidential to
Single channel data transceiver module WIZ2-434
Single channel data transceiver module WIZ2-434 Available models: WIZ2-434-RS: data input by RS232 (±12V) logic, 9-15V supply WIZ2-434-RSB: same as above, but in a plastic shell. The WIZ2-434-x modules
VSCOM USB PRO Series Industrial I/O Adapters
VSCOM USB PRO Series Industrial I/O Adapters 1.Introduction The VSCOM USB PRO Series Industrial I/O Adapters are advanced USB to Serial Adapters that connect to 1, 2, 4 or 8 RS-232/422/485 serial devices.
DV-1D Data/Voice DSU TABLE OF CONTENTS SECTION 1 - DESCRIPTION...2 SECTION 2 - SPECIFICATIONS...8 SECTION 3 - INSTALLATION...11
DV-1D Data/Voice DSU TABLE OF CONTENTS SECTION 1 - DESCRIPTION...2 SECTION 2 - SPECIFICATIONS...8 SECTION 3 - INSTALLATION...11 SECTION 4 - OPERATION...18 SECTION 5 - FRONT PANEL CONTROLS AND INDICATORS...25
Cisco Modular Access Router Cable Specifications
Cisco Modular Access Router Cable Specifications This document provides cable specifications for Cisco 1800 series, Cisco 2600 series, Cisco 2800 series, Cisco 3600 series, Cisco 3700 series, and Cisco
Chapter 4 T1 Interface Card
Chapter 4 T1 Interface Card GENERAL This chapter describes DTE interface options that may be required if application requirements change. It also describes software configuration for the T1 interface card.
RS-422/485 Multiport Serial PCI Card. RS-422/485 Multiport Serial PCI Card Installation Guide
RS-422/485 Multiport Serial PCI Card Installation Guide 21 Contents 1. Introduction...1 2. Package Check List...2 3. Board Layouts and Connectors...3 3.1 2S with DB9 Male Connectors...3 3.1.1 JP5: UART
Date Rev. Details Author
Jtech engineering ltd J - Te c h E n g i n e e ring, L t d. 11080 Bond Boulevard Delta BC V4E 1M7 Canada Tel: 604 543 6272 Fax: 604 543 6476 http://www.jtecheng.com AUTODIALER USER S MANUAL REVISION HISTORY
An0067. Cable-set Reference Guide. Rev. 2.0 - December 2007 - ETH_An0067_USM20-2007- 12
An0067 Cable-set Reference Guide Rev. 2.0 - December 2007 - ETH_An0067_USM20-2007- 12 2 Introduction Disclaimer The information in this manual has been carefully checked and is believed to be accurate.
IP SERIAL DEVICE SERVER
IP SERIAL DEVICE SERVER ( 1 / 2 / 4 serial port ) Installation guide And User manual Version 1.0 1Introduction... 5 1.1Direct IP mode...5 1.2Virtual COM mode...5 1.3Paired mode...6 1.4Heart beat... 6
KOM200. Industrial Serial to Fiber Media Converter. User s Manual
KOM200 s Manual 200911 KOM200 Industrial Serial to Fiber Media Converter s Manual KYLAND Technology Co., Ltd. 1 KOM200 s Manual 200911 Table of contents CHAPTER 1: PRODUCT OVERVIEW---------------- 3 CHAPTER
Contents. SPECIFICATIONS AND FEATURES GUIDE NI Serial Hardware
SPECIFICATIONS AND FEATURES GUIDE NI Serial Hardware This document lists safety and compliance information for NI Serial hardware, as well as physical specifications, software features, and recommended
Maestro Heritage. GSM GPRS Modem 850 / 900 / 1800 / 1900 USER MANUAL Rev. 03
Maestro Heritage GSM GPRS Modem 850 / 900 / 1800 / 1900 USER MANUAL Rev. 03 www.maestro-wireless.com Email: [email protected] Tel: 852 2869 0688 Fax: 852 2525 4701 Address: Room 3603-3609, 36/F,
2-Port RS232/422/485 Combo Serial PCI Card
2-Port RS232/422/485 Combo Serial PCI Card Installation Guide 1. Introduction Thank you for purchasing this 2-Port RS232/422/485 Combo Serial PCI Card. It is a universal add in card that connects to a
DEX28-VR3P Quick Installation Guide
DEX28-VR3P Quick Installation Guide DEX28-VR3P PBX DTSs 1 3 5 2 4 6 Procedure to start recording: 1. Connect ODD ports (1, 3 or 5) to PBX (MD110 ELU28 or MX-ONE ELU33 board) 2. Connect EVEN ports (2, 4
Auxiliary equipment for communication with the EuroProt protective devices
Auxiliary equipment for communication with the EuroProt protective devices RS232 cable This cable is used to connect the RS232 connector located on the front panel of the EuroProt devices to the 9 pin
Cisco CCNA Optional Semester 4 Labs Wide Area Networking LAB 1 T1 TSU WAN LINK OVERVIEW - Instructor Guide (Estimated time: 30 minutes)
CNAP @ VCC 1 of 8 LAB 1 T1 TSU WAN LINK OVERVIEW - Instructor Guide (Estimated time: 30 minutes) Objectives: Understand the function of a T1 Service Unit (TSU) in network telecommunications Connect routers
Power, Cable, and Antenna Connection Procedures
CHAPTER 4 Power, Cable, and Antenna Connection Procedures This chapter describes how to connect your Cisco 1800 series fixed-configuration router to a power source and to networks and external devices.
PCMCIA 1 Port RS232 2.1 EDITION OCTOBER 1999
232 232232 PCMCIA 1 Port RS232 2.1 EDITION OCTOBER 1999 Guarantee. FULL 36 MONTHS GUARANTEE. We guarantee your interface card for a full 36 months from purchase, parts and labour, provided it has been
Fanuc 0 M/T Model C Serial (RS232) Connection Guide
Memex Automation Inc., Burlington, Ontario Canada L7N 1 http://www.memex.ca Fanuc 0 M/T Model C Serial (RS232) Connection Guide The Fanuc 0-C control has two RS-232 interfaces. Interface number 1 (M5)
APPLICATION NOTE. Leased Line Modem. Leased Line Modem...3. Introduction... 3. Key Concepts... 4
Issue Date 02/18/02 APPLICATION NOTE Leased Line Modem Leased Line Modem...3 troduction... 3 Key Concepts... 4 Application Details...4 Theory of Operation...6 Components...8 Planning Considerations...10
Stevens Cell-Net CDMA & GSM M2M 3G Data Modem. Product Manual
Stevens Cell-Net CDMA & GSM M2M 3G Data Modem Product Manual Stevens Part #93950A (GSM) Stevens Part #93950B (Verizon) updated: July 2015 Contents 2. Technical Specifications... 4 2.1 Features... 4 2.2
PROPRIETARY INFORMATION NOTICE
2012 LX I Technologies, Inc. Engineering Department [LEASED LINE MODEM LXV92] This document will cover the operations and installation on the LXV92 92 lease line modem. This modem is designed to work with
Telebyte 209 Short Haul Modem
Telebyte 209 This document provides installation instructions for the Telebyte 209 (Keri Systems P/N SHM-232). This short haul modem can be used to assist in long-distance, direct, connections between